AC Repair in Litchfield Park, AZ: How to Repair 3 Typical Problems

There can be a couple of explanations why your AC equipment won’t cool: a triggered circuit breaker, incorrect thermostat settings, a turned off switch or an overflowing condensate drain pan.

Your air conditioning won’t turn on when you have a tripped breaker.

To determine if one has blown, find your residence’s main electrical panel. You can locate this gray device on the wall in the basement, garage or closet.

• Make sure your hands and feet are free of moisture before you check the panel or breakers.
• Look for the breaker labeled “AC” and make sure it’s in the “on” position. If it’s overloaded the breaker will be in the in between or “off” location.
• Quickly shift the breaker back to the “on” location. If it instantaneously trips again, leave it alone and reach us at 623-208-6444. A switch that keeps turning off may indicate your residence has electrical trouble.

If your thermostat isn’t signaling your system to run, it won’t turn on.

The first part is checking it’s set to “cool” and not “heat.” Otherwise your AC will probably not switch on. Or you could receive. hot air moving from vents since the heater is on instead.

If you rely on a traditional thermostat:

• Put in new batteries if the screen is blank. If the readout is displaying scrambled characters, buy a new thermostat.
• Make sure the right option is showing. If you can’t change it, reverse it by dropping the temperature and pushing the “hold” button. This will force your AC to work if scheduling is not right.
• Test setting the thermostat 5 degrees lower than the room’s temperature. Your AC won’t start if the thermostat matches the room’s temperature.

Once your thermostat is adjusted correctly, you should start getting cool air promptly.

If you rely on a smart thermostat, like one made by Nest, Ecobee, Lux, Honeywell or Bosch, look at the manufacturer’s website for troubleshooting. If you still can’t get it to work, reach us at 623-208-6444 for assistance.

Your cooling equipment typically has a shut-off device by its outside unit. This switch is typically in a metal box hung on your residence. If your equipment has recently been repaired, the switch may have inadvertently been placed in the “off” position.

Condensate drain pans hold the extra liquid your air conditioner pulls from the air. This pan can be situated either beneath or inside your furnace or air handler.

When there’s a clog or backed up drain, water can build up and prompt a safety control to turn off your unit.

If your pan includes a PVC pipe or drain, you can clear the surplus condensation with a special pan-cleaning tablet. You can purchase these capsules at a home improvement or hardware retailer.

If your pan includes a pump, locate the float switch. If the lever is “up” and there’s moisture in the pan, you may need to replace the pump. Call us at 623-208-6444 for support.

If your air conditioner is working but not providing cold air, its airflow may be blocked. Or it could not have sufficient refrigerant.

Your equipment’s airflow can be decreased by a clogged air filter or filthy condenser.

A filthy filter can cause numerous issues, such as:

• Limited comfort
• Frozen refrigerant lines or evaporator coil
• Intermittent cooling
• Larger electricity bills
• Causing your system to break down more quickly

We propose replacing flat filters every four weeks, and pleated filters every three months.

If you can’t recall when you last replaced yours, shut off your AC totally and remove the filter. You can spot the filter in your furnace or air pump’s blower compartment. It might also be found in a connected filter holder or wall-mounted return air grille.

Tilt the filter up to the sunshine. If you can’t see through it you certainly should get a new one.

Weeds, vegetation and shrubbery can get in the way of your condensing system. This can reduce its airflow, impact its energy efficiency and impact your comfort. Here’s a method you can follow to get your unit running properly again.

1. Turn off electricity totally at the breaker or outside switch.
2. Get rid of plant rubbish around the AC. Once you’ve removed bigger debris within a two-foot range, you can use a soft brush or vacuum to gingerly remove dirt from the equipment’s fins. Misshapen fins can also affect effectiveness, so you can attempt to straighten them with a blunt knife.
3. Use a hose nozzle to slowly take off dirt on the fins from inside the unit. Be careful to avoid getting water on the fan motor.
4. Install the top again and restore the power.

When AC units don’t have sufficient refrigerant, they’ll struggle to remove heat and humidity from your residence.

Here are a few symptoms that your unit is losing refrigerant:

1. It takes an extended amount of time to lower the temperature in your space and you’re constantly decreasing the temperature on the thermostat.
2. Cooling blowing through the ducts isn’t as cold as it should be.
3. You’re noticing whistling or burbling noises when the air conditioning runs.
4. Your evaporator coil is frozen as a result of having trouble handling humidity.

Suspect your equipment is leaking refrigerant? You need a licensed heating and cooling service specialist to fix the leak and restore the proper level of refrigerant in your equipment. Call us at 623-208-6444 for assistance.

When it feels like you’re not getting adequate amounts of cold air, there’s possibly an obstruction or detachment within your air conditioning equipment.

• The beginning place is examining your air filter. Replace it if it’s filthy.
• Then ensure the ductwork is free throughout your rooms.
• If you’re still not experiencing adequate chilled air, you should have your ducts examined by a professional like Cooler Tymes LLC. Your duct system might need to be fixed or hooked up again in tricky locations like your attic, basement or crawl space.